how to read water corp sewer plans

The Sanitary Sewer Plan and Profile Drawings Creation is usually one of the most tedious and delicate tasks. Western Water has detailed plans and strategies to ensure optimal management of our business, deliver the best possible service to the community, and to meet regulatory requirements. More complicated projects require dozens of wall sections to describe all the various conditions.No set of plans is perfect. To shift the risk of these conflicts to the builder, architects will often include language to the effect that “should a conflict arise, the contractor shall provide the greater QUALITY and/or QUANTITY of what was shown.” So it’s extremely important to make sure you understand how the various drawings relate to one another and to verify that the information called for is consistent.Many building components are organized in simple matrices called ‘schedules.’ Door, frame and door hardware details will be described in a door schedule. They show the location of the connection point in relation to the cadastral boundaries.I can't see much of the plan, so I don't see what manhole you are reffering to. Multiple addenda are common, and some sheets may be re-issued several times during the project. Pipes 300mm or greater are classified as main Wastewaters. This is where ‘sections’ are used. What you should look for is whether the manhole itself or and pipes are within the boundary of the property in question.

The legend refers to square and circular symbols as "Manhole information boxes" That box is in the property that I am interested in. From a simple residence to a large commercial building project, the same basic drawings and related information are required in order to obtain permits, estimate costs, establish a construction schedule, and ultimately construct the project.These basic terms should help you better understand how a set of plans is organized and how to read plans and blueprints.Similar to building a model or assembling something from written diagrams and directions, scan the entire set of plans first and read the various notes and specifications. The manholes are positioned at bends in the lines and at regular intervals for maintenance. Many contractors have made the mistake of estimating only what was shown on the plans, missing a note that may say “typical at all floors.” As buildings and the systems within them have become increasingly complex, so have the two-dimensional drawings that describe all the details of the project. A property sewerage plan will allow you and your building professionals to identify where the sewerage systems and any City West Water assets are located on your property. The location of the "Manhole information box" within a boundary doesn't mean anything, they are placed wherever they can be clearly read and will easily identify the manhole they describe.

Make sure you know what scale you should be using as you proceed with your estimate; using the wrong scale can drastically alter your quantities.When reading plans and blueprints, the most common architectural plan view scales are ⅛”=1’ and ¼”=1’. Knowing how to read construction plans and blueprints is critical whether you’re a general contractor, a sub-contractor or a tradesman. Water Corporation maintains records for all land including the name and address of the owner of the land, the account number, charges and unpaid charges. This will give you an overall impression up front, before you start to drill down to specifics.These are the basic views looking down at a horizontal plane.Use the right scale and check that the scale shown is correct on the plans. Manholes are shown as either filled in dots or empty circles. As buildings and the systems within them have become increasingly complex, so have the two-dimensional drawings that describe all the details of the project. ; Structural sheets are S-1, S-2 and so on for Mechanical, Plumbing and Electrical Sheets (M, P and E).Every drawing sheet will have a small “revision” block along the margin. The three main types of sewerss are: MAIN SEWER MS displayed Pipes 450mm in diameter or greater, flowing to a Treatment Plant or Main Pumping Station COLLECTION CS displayed Pipes …

For example, a masonry wall when viewed in section will normally be shown with a 45-degree cross-hatching through the wall. They show the location of the connection point in relation to the cadastral boundaries. This insures the user has the current sheet and allows for quick reference to previous versions for comparison.Architects are in a hurry like everyone else. Gypsum board is usually shown with small dots between the two faces. There are various ways to access plans. Cheers.In this case the sewer lines are in the road reserve. These standardized graphics help the architect, engineer and builder communicate more clearly.Building plans are not static and will typically evolve over the life of the project. Sections are basically ‘slices’ through a building or building component.A common ‘section’ is a Wall Section. As you start to review any construction plan, familiarize yourself with those symbols and what they mean.The scale (or relationship between drawing dimensions and real dimensions) used for various drawings will change, depending on what information is being shown. This allows much more information to be shown.Architects and engineers use some basic graphics to describe specific building elements. In our beginner’s guide on how to read construction plans we will cover the basics of what plans are, what sort of information they contain, and how to interpret that information. Sections are cross referenced on plan views, and elevations, so the reader can understand where the relevant ‘slice’ was taken. (I can't remeber the distinction, I haven't actually worked with watercorp assets for a few years)Sorry about that, here is a broader screenshot. Dial Before You Dig. Somersoft has been archived - you can continue the discussion at PropertyChat Please call (08) 9273 4520 to make an appointment to inspect these records. For example a symbol used on an architectural plan, may mean something entirely different on the electrical plan.To clarify their intent, the architect or engineer provides a key, typically on the first sheet, that relates the symbols and their intended meaning. Then fold back the lower corner of the older sheet, tape it on the back and mark it as VOID next to the sheet number.